Views: 0 Author: Site Editor Publish Time: 2026-11-18 Origin: Site
Industries such as chemical manufacturing, power generation, textile processing, and metallurgy produce flue-gas desulfurization wastewater, reverse-osmosis concentrate, cleaning liquids, and high-salinity process mother liquors. These streams can be costly to treat and manage, so plants need solutions that address discharge requirements, operating costs, and resource recovery together.
A spray dryer atomizes a suitable wastewater concentrate into fine droplets and brings them into contact with a hot gas stream. Water evaporates, while salts and nonvolatile solids are collected as dry residues. In flue-gas desulfurization applications, spray-drying systems can use hot flue gas for evaporation and downstream dust collectors to capture the dried products.
Within a zero liquid discharge (ZLD) strategy, spray drying can perform the final drying and solids-collection steps for concentrated liquid streams. It works alongside pretreatment, evaporation or concentration, exhaust-gas treatment, water recovery, and residue management.
A typical process route is:
Wastewater collection and analysis → Pretreatment → Concentration or conditioning → Atomization and drying → Solids collection → Exhaust treatment and water reuse
The process begins with an analysis of salinity, solids content, viscosity, pH, suspended matter, oil content, and volatile components. Filtration, oil removal, softening, or other pretreatment can then be selected to stabilize the feed and reduce scaling or blockage risks.
A pump delivers the conditioned or concentrated liquid to the spray dryer. The atomizer forms fine droplets, and the hot gas removes moisture. Nonvolatile salts and solids become dry particles that are collected in the drying chamber, a cyclone separator, a bag filter, or a combination of collection equipment.
The water-recovery route is designed around the project target. In direct flue-gas spray evaporation, water vapor travels with the exhaust stream into the downstream gas system. A system with a condensation stage can recover water for reuse after its quality has been tested. Volatile components in the feed are addressed through suitable exhaust monitoring and treatment.
Spray drying evaporates water and gathers salts and solid residues in a dry form. This reduces the volume of liquid requiring storage, transport, or further treatment. The achievable reduction is calculated from the feed moisture, pre-concentration level, throughput, and target residual moisture, allowing each plant to set a process-specific reduction goal.
Plants with boiler flue gas, gas-turbine exhaust, or kiln waste heat can assess these sources as part of the dryer heat balance. Power-generation facilities already use hot flue gas to evaporate desulfurization wastewater. A project energy review should account for wastewater flow, initial moisture, available gas temperature, operating hours, and required water recovery.
Some high-salinity process streams contain inorganic salts or metal-bearing compounds with recovery potential. Spray drying converts these streams into solids that are easier to collect, sample, and route to downstream separation, crystallization, purification, or resource-recovery steps. Product use and value are established through composition and purity testing.
Flue-gas desulfurization wastewater: Hot flue gas or a dedicated heat source evaporates the wastewater, while salts and solid particles are collected downstream.
Reverse-osmosis concentrate and high-salinity brines: Pretreated or concentrated streams can be further dried to reduce liquid waste and support a ZLD process route.
Chemical mother liquors and cleaning liquids: Streams with known composition and stable pumping and atomization behavior can be evaluated for spray drying.
Landfill-leachate concentrate: Water analysis, pretreatment, and exhaust-treatment requirements guide the process assessment and system design.
Select wetted materials from water chemistry. Chloride concentration, acidity or alkalinity, operating temperature, and cleaning media guide the choice of stainless steel, alloys, linings, or coatings.
Match the atomizer to the feed. For liquids with suspended solids, crystallizing salts, or higher viscosity, particle size and solids loading inform the flow passage, atomization method, and cleaning arrangement. Feed trials confirm stable continuous operation.
Provide suitable exhaust and dust collection. Cyclones, bag filters, and gas-treatment equipment are selected according to feed composition and emission requirements, with controls for particulate matter and volatile components.
Plan for residue testing and management. Collected salts and solids are analyzed to determine the appropriate recovery route or compliant disposal method.
Spray drying provides an effective route for suitable flue-gas desulfurization wastewater, high-salinity concentrates, and selected chemical liquid wastes. By evaporating water and collecting dry residues, it reduces liquid waste streams. Integrated with pretreatment, concentration, exhaust treatment, water recovery, and residue management, it can support a plant’s ZLD and water-reuse objectives.
For equipment planning, provide the wastewater source and composition, daily flow rate, moisture content, available heat source, water-reuse target, and residue-management requirements. Material testing and an energy balance help define the atomization method, materials of construction, treatment capacity, and supporting equipment.
Contact us: info@machtechdryer.com
SPRAY 007 - Spray Drying in Lithium Battery Material Production
SPRAY 005 - What Factors Affect The Particle Size of Spray-dried Powder
SPRAY 004 - How To Select Spary Dryer From R&D To Production
Spray 003 - Centrifugal Vs. Pressure Spray Drying: Which Is Right for Your Production Line?
Spray 001 - What Is A Spray Dryer? Working Principles & Core Advantages
Contact Us